$4,970.90

This custom kit is designed to provide a ready to go Maker Space for High School students looking to get started with micro:bit and programming. While not all components work directly with micro:bit they are all designed for High School students and should all work well with a micro:bit curriculum.

SKU: PL-SU-Spark_HS_micro Category:

• SparkFun Inventor’s Kit for micro:bit Lab Pack x3
• 10x SparkFun Inventor’s Kit for micro:bit
• micro:bit Board
• SparkFun micro:bit Breakout (with Headers)
• Full-Size Breadboard
• micro:bit Battery Holder — 2xAA
• Small Servo
• TMP36 Temperature Sensor
• Photocell
• USB Micro-B Cable — 6 Foot
• Jumper Wires
• Alligator Clips with Pigtails
• RGB Diffused LED
• Red, Blue, Yellow and Green LEDs
• 10K Trimpot
• Multicolor Button — 4-pack
• SPDT Mini Power Switch
• Mini Speaker
• 100 Ohm Resistors (Thick Leads)
• 10K Ohm Resistors (Thick Leads)
• 1x SparkFun Inventor’s Kit Refill Pack — v4.0
• Adjustable Parts Box
• Mini Speaker x2
• Temerature Sensor – TMP36 x2
• Mini Photocell x2
• Trimpot 10k x2
• Mini Power Switch – SPDT x2
• Generic Servo (Sub-MiroSize) x2
• Assorted LED 2-pack (5 Red, 5 Blue, 5 Yellow, 5 Green)
• Multicolor Button 4-pack (Red, Blue, Yellow, Green) x2
• 25x Alkaline Battery — AA
• gator:bit x5
• gator:control ProtoSnap board x5
• gator:button board x2
• gator:switch board x2
• gator:color x5
• White gator:LED Board x2
• Red gator:LED Board x2
• Green gator:LED Board x2
• Blue gator:LED Board x2
• Yellow gator:LED Board x2
• Powewr Rail Board x2
• gator:starter x5
• gator:temperature Board
• gator:light Board
• gator:RGB Board
• micro:arcade kit x5
• SparkFun gamer:bit
• Arcade Joystick
• Red Concave Button
• Blue Concave Button
• Yellow Concave Button
• Green Concave Button
• micro:bit Battery Holder — 2xAA
• Spade Connector Wire (3ft, Female) x16
• micro:climate kit x5
• SparkFun weather:bit
• Weather Meters
• SparkFun Soil Moisture Sensor
• SparkFun OpenLog
• Waterproof Temperature Sensor
• micro:bit Battery Holder – 2xAA
• Pocket Screwdriver Set
• Jumper Wire (12in. M/M) x10
• micro:bot kit x5
• SparkFun moto:bit
• Shadow Chassis
• SparkFun RedBot Sensor — Line Follower x3
• Sub-Micro Servo x2
• Hobby Gearmotor x2
• Wheel — 65mm (Rubber Tire, Pair) x2
• Jumper Wire — 3-pin, 6″ x3
• Paper Circuits Classroom Pack x2
• Printed Robot Template Card x30
• Red LED – 5mm x30
• Blue LED – 5mm x30
• Yellow LED – 5mm x30
• Green LED – 5mm x30
• Coin Cell Battery – CR2032 x30
• Copper Tape – 1ft x30
• Copper Tape – 50ft roll x1
• Binder Clip x30
• Beginner Parts Kit x5
• Adjustable Parts Box
• 0.1uF Cap x10
• 100uF Cap x5
• 10uF Cap x5
• 1uF Cap x5
• 10nF Cap x5
• 1nF Cap x5
• 100pF Cap x5
• 10pF Cap x5
• 1N4148 Diode x5
• 1N4001 Diode x5
• 2N3906 PNP Transistor x5
• 2N3904 NPN Transistor x5
• 20-pin Female Header x3
• 20-pin Male Header x3
• Mini Power Switch x3
• Push Buttons x2
• 10K Trimpot x1
• LM358 OpAmp x2
• 3.3V Regulator x2
• 5V Regulator x2
• 555 Timer
• Green LED
• Yellow LED
• Red LED
• 7-Segment Red LED
• Mini Photocell
• Essenstial Sensor Kit x5
• Triple Axis Accelerometer Breakout – MMA8452Q
• Hall Effect Sensor
• Tilt Sensor
• Piezo Element
• Insulated Reed Switch
• IR Receiver Diode
• Infrared LED
• TMP36 – Temperature Sensor
• Trimpot 10K with Knob
• 0.25″ Magnet Square
• 0.5″ Force Sensitive Resistor
• Mini Photocell
• Flex Sensor
• Piezo Buzzer/Speaker x2
• Resistor 1.0M Ohm 1/6 Watt PTH x2
• Deluxe Tool Kit x5
• Weller WLC100 Soldering Station
• Heaterizer XL-3000 Heat Gun
• Digital Multimeter – Basic
• Insulated Silicone Soldering Mat
• SparkFun Third Hand Kit
• Pocket Screwdriver Set
• Monocle Magnifier – Illuminated
• Solder – 1/4lb Spool (0.032in.) Special Blend
• Solder Wick #2 5ft. – Generic x2
• Solder-Mate Solder Dispenser
• Soldering Tip – Weller – Standard (ST1)
• Solder Tip Tinner and Cleaner
• Chip Quik No-Clean Flux Pen – 10mL
• Hook-Up Wire – Assortment (Solid Core, 22 AWG)
• Heat Shrink Kit
• Wire Strippers – 22-30AWG
• Flush Cutters – Xcelite
• Needle Nose Pliers
• Tweezers – Straight (Cross-Lock, ESD Safe)
• Tweezers – Curved (ESD Safe)
• Hobby Knife
• SparkFun Safety Glasses
• Water Bottle – 2oz
• Simon PTH Kit x30
• 1x ATmega328 – pre-programmed with Simon firmware
• 1x Buzzer
• 2x 0.1μF Cap
• 1x 10K Resistor
• 4x LEDs (blue, yellow, red, green)
• 2x Slide Switch
• 4x Battery Clips
• 2x AA Batteries
• 1x Button pad
• 1x Bezel
• 4x Standoffs and screws
• 1x Assembly instructions m/products/11046)
• Water Bottle – 2oz

filed under: